Remote Eth. I/O W/ 4Ai, 4Di, 4Dio, And 2Port Swtch, M1Iologike1242
| Mounting | DIN rail or wall |
|---|---|
| Protection | 1.5 kV magnetic isolation |
| Pulse Output Frequency | 500 Hz |
| EMI | EN 55022; EN 61000-3-2; EN 61000-3-3; FCC Part 15, Subpart B, Class A |
| Storage temperature | -40 to 85°C |
| Type | Sink, Differential input |
| Isolation | 3k VDC or 2k Vrms |
| Ambient Relative Humidity | 5 to 95% (non-condensing) |
| Shock | IEC 60068-2-27 |
| Time | 502,210 hrs |
| Accuracy | ±0.1% FSR @ 25°C; ±0.3% FSR @ -10 and 60°C; ±0.5% FSR @ -40 and 75°C |
| Dry Contact | On: short to GND; Off: open |
| Input Impedance | 10M ohms (min.) |
| Over-voltage Protection | 45 VDC |
| Analog Inputs | 4 channels |
| Digital Inputs | 4 channels |
| Counter Frequency | 250 Hz |
| Input Range | 0 to 10 VDC, 0 to 20 mA, 4 to 20 mA |
| Built-in Resistor for Current Input | 120 ohms |
| Wiring | I/O cable max. 14 AWG |
| Common Type | COM, 4 points |
| Freefall | IEC 60068-2-32 |
| Dimensions | 27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in) |
| Database | Telcordia (Bellcore) |
| Current Rating | 200 mA per channel |
| I/O Mode | DI or Event Counter, Voltage / Current, DO or Pulse Output |
| Over-temperature Shutdown | 175°C (typical), 150°C (min.) |
| Digital Filtering Time Interval | Software Configurable |
| Power Input | 24 VDC nominal, 12 to 36 VDC |
| Power Consumption | 139 mA @ 24 VDC |
| EMS | EN 55024, EN 61000-4-2, EN 61000-4-3; EN 61000-4-4, EN 61000-4-5, EN 61000-4-6; EN 61000-4-8, EN 61000-4-11 |
| Sampling Rate | All channels: 12 samples/sec; Per channel: 3 samples/sec; Only one channel enabled: 12 samples/sec |
| Altitude | Up to 2,000 m |
| Sensor Type | Wet Contact (NPN or PNP), Dry Contact |
| Operating temperature | Standard Models: -10 to 60°C (14 to 140°F); Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
| Vibration | IEC 60068-2-6 |
| Ethernet | 2 switched 10/100 Mbps RJ45 ports |
| Configurable DI/Os | 4 channels |
| Resolution | 16 bits |
| Protocols | Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, HTTP |
| Safety | UL 508 |
| Hazardous Location | UL/cUL Class I Diision 2, ATEX Zone 2 |
| Over-current Protection | 2.6 A |
| Wet Contact (DI to COM) | On: 10 to 30 VDC; Off: 0 to 3 VDC |
| Package Quantity | 1 |