The high-torque PKP series stepper motor offers balanced performance enhanced by high torque, low vibration and low noise.Unipolar WindingMotor cable required (sold separately)
| Holding Torque | 0.124 N*m |
|---|---|
| Step Angle | 0.9 deg |
| Motor Frame Size | 28 mm |
| Input Current | 0.95 |
| Input Voltage | 4.4 V |
| Shaft Diameter | 5 mm |
| Integrated Brake | Not Equipped |
| product line | VEXTA® |
| motor type | 2-Phase |
| basic step angle | 0.9º |
| frame size | 28 mm |
| frame size(imperial) | 1.1 in |
| motor length | 51.5 mm |
| motor length(imperial) | 2.42 in. |
| motor connection type | Connector |
| holding torque(imperial) | 17.5 oz-in |
| current per phase (a/phase) | 0.95 |
| voltage (vdc) | 4.4 |
| resistance (ω/phase) | 4.6 |
| inductance (mh/phase) | 3.2 |
| shaft/gear type | Round Shaft with Flat (No Gearhead) |
| output shaft diameter | 5 mm |
| shaft | Single |
| power input | DC |
| encoder | Not Equipped |
| electromagnetic brake | Not Equipped |
| connection type | Unipolar |
| lead wires | 6 |
| rotor inertia | 17x10 -7 kg·m² |
| rotor inertia(imperial) | 0.093 oz-in² |
| rohs compliant | These products do not contain substances that exceed the regulation values in the RoHS Directive. |
| insulation class | Class B [266ºF (130ºC)] |
| insulation resistance | 100 MΩ or more when 500 VDC megger is applied between the windings and the case under normal ambient temperature and humidity. |
| dielectric strength | Sufficient to withstand 0.5 kVAC at 60 Hz applied between the windings and the case for 1 minute under normal ambient temperature and humidity. |
| temperature rise | Temperature rise of the windings is 144ºF (80ºC) or less measured by the change resistance method. (at rated current, at standstill, 2 phases energized) |
| ambient temperature range | 14 ~ 122ºF (-10 ~ 50ºC) (non-freezing) |
| ambient humidity | 85% or less (Non-Condensing) |
| shaft runout | 0.05 mm (0.002 in.) T.I.R. |
| stop position accuracy | ±3 arc minutes (±0.05º) |
| radial load | 0 mm from Shaft End = 25 N 5 mm from Shaft End = 34 N 10 mm from Shaft End = 52 N |
| radial load(imperial) | 0 in. from Shaft End = 5.6 lb 0.2 in. from Shaft End = 7.6 lb 0.39 in. from Shaft End = 11.7 lb |
| axial load | 5 N |
| axial load(imperial) | 1.12 lb |
| radial play | 0.025 mm (0.001 in.) maximum of 5 N (1.12 lb.) |
| axial play | 0.075 mm (0.003 in.) T.I.R. |
| concentricity | 0.075 mm (0.003 in.) T.I.R. |
| perpendicularity | 0.075 mm (0.003 in.) maximum of 10 N (2.2 lb.) |
| permissible thrust load | The permissible thrust load shall be no greater than the motor mass. |
| Unidad | piece |
| Cantidad mínima | 1 |
| Incremento de cantidad | 1 |
| Fabricante | Oriental Motor |
| Vendor SKU | PKP225MU09A |
| Lead Time | Estimated Ship: 10/22/2024 |