Submersible Pump Motor, Bearing Protection Not Applicable, Body Dia. 3.8 in, Bolt Circle Dia. 2 7/8 in, CC Number Not Applicable, Conduit Box Location Not Applicable, Conduit Box Position Not Applicable, Diaphragm Type Pressure Equalizing, Duty Cycle Continuous, Finish Not Applicable, Frame Not Applicable, Hz 60 Hz, Full Load Amps 10.0, Height 11 in, HP 1/2, Includes Not Applicable, Ins. Class B, Inverter Rated No, Inverter Rating Not Applicable, Lead Length 4 ft, Length Less Shaft 9 1/2 in
| Item | Submersible Pump Motor |
|---|---|
| Phase | Single |
| HP | 1/2 |
| Voltage | 115V AC |
| Number of Wires | 3 |
| RPM Range | 1,725 to 3,450 |
| Motor Service Factor | 1.15 |
| Motor Bearings | Kingsbury |
| Nameplate RPM | 3,450 |
| Stator Type | Hermetically Sealed |
| Thrust Rating | 300 lb |
| Motor Shaft Rotation | CCW |
| Motor Enclosure Design | Hermetically Sealed |
| Motor Sub Application | Water Wells |
| Hz | 60 Hz |
| Height | 11 in |
| Max. Ambient Temp. | 86 deg F |
| Overload Relay Amp Setting | 10.0 A |
| Overload Relay Max. Amp Setting | 12 A |
| Motor Application | Pumps |
| Standards | ANSI/NSF 61 |
| Diaphragm Type | Pressure Equalizing |
| Motor Design | Capacitor-Start, Run |
| Starter Required | No |
| Motor Thermal Protection | Built-In Lightning Arrestor |
| Shaft Material | Nitrile Rubber |
| Overload Relay Required | No |
| Full Load Amps | 10 A |
| Max. SF Amps | 12:00 AM |
| Lead Length | 4 ft |
| No. of Speeds | Not Applicable |
| Ins. Class | B |
| Overall Length | 9-1/2 in |
| Conduit Box Position | Not Applicable |
| NEMA Design | Not Applicable |
| Length Less Shaft | 9-1/2 in |
| Duty Cycle | Continuous |
| Inverter Rated | Not Inverter Rated |
| Body Dia. | 3.8 in |
| Inverter Rating | Not Applicable |
| Shaft Length | 10-1/8 in |
| Bearing Protection | Not Applicable |
| Part Winding Start Capable | No |
| Bolt Circle Dia. | 2-7/8 in |
| Regreasable Bearings | Not Applicable |
| Nominal Efficiency | 56% |
| Motor Mounting Type | NEMA Pump Mounting |
| Ring to Ring Center | Not Applicable |
| Motor Frame Material | Stainless Steel |
| Shaft Dia. | 5/8 in |
| Manufacturers Warranty Length | 1 yr |
| Conduit Box Location | Not Applicable |
| Frame | Not Applicable |
| Motor Mounting Position | Vertical Shaft Up |
| Weight | 19 lb |
| Finish | Not Applicable |
| Includes | Not Applicable |
| CC Number | Not Applicable |
| Motor Shaft Design | Splined |
| Resilient Ring Dia. | Not Applicable |
| Efficiency Rating | Not Applicable |
| Resilient Ring Diameter | Not Applicable |
| Includes Diaphragm | Diaphragm Included |
| Number of Speeds | Not Applicable |
| Body Diameter | 3.8 in |
| Overload Relay Current | 10 A |
| Motor Enclosure Type | Totally Enclosed Non-Ventilated |
| Shaft Design | Splined |
| Overload Relay Maximum Amp Setting | 12 A |
| Frequency | 60 Hz |
| Bearing Lubrication Type | Not Applicable |
| NEMA Design Class | Not Applicable |
| Product Type | Pump Motor |
| Application | Pump |
| Frame Material | Stainless Steel |
| Frame Size | Not Applicable |
| Mounting Position | Vertical Shaft Up |
| Bearing Protection Type | Not Applicable |
| Ring-to-Ring Center | Not Applicable |
| Insulation Class | B |
| Requires Overload Relay | No |
| Nameplate Service Factor @ 60 Hz | 1.15 |
| Sub Application | Deep Well Submersible Pump |
| Bearing Type | Kingsbury |
| Bolt Circle Diameter | 2-7/8 in |
| Includes Low Temperature Monitor | Low Temperature Monitor Not Included |
| Service Factor Current | 12 A |
| Shaft Diameter | 5/8 in |
| Manufacturers Warranty | 1 yr |
| Series | 4" SUPER STAINLESS SUBMERSIBLE MOTORS |
| Frame Finish | Not Applicable |
| Full Load Current @ 60 Hz | 10 A |
| Wire Rope Length | 9-1/2 in |
| Length | 9-1/2 in |
| Country of Origin (subject to change) | Mexico |
| Package Quantity | 1 |