Submersible Pump Motor, Bearing Protection Not Applicable, Body Dia. 3.8 in, Bolt Circle Dia. 2 7/8 in, CC Number Not Applicable, Conduit Box Location Not Applicable, Conduit Box Position Not Applicable, Diaphragm Type Pressure Equalizing, Duty Cycle Continuous, Finish Not Applicable, Frame Not Applicable, Hz 60 Hz, Full Load Amps 8.0, Height 10 1/4 in, HP 1/3, Includes Not Applicable, Ins. Class B, Inverter Rated Not Inverter Rated, Inverter Rating Not Applicable, Lead Length 4 ft
| Item | Submersible Pump Motor |
|---|---|
| Phase | Single |
| HP | 1/3 |
| Voltage | 115V AC |
| Number of Wires | 2 |
| RPM Range | 1,725 to 3,450 |
| Motor Service Factor | 1.15 |
| Motor Bearings | Kingsbury |
| Nameplate RPM | 3,450 |
| Max. SF Amps | 9.2 A |
| Overload Relay Max. Amp Setting | 12 A |
| Max. Ambient Temp. | 86 deg F |
| Motor Enclosure Design | Hermetically Sealed |
| Motor Shaft Rotation | CCW |
| Lead Length | 4 ft |
| Shaft Material | Nitrile Rubber |
| Motor Sub Application | Water Wells |
| Overload Relay Required | No |
| Motor Design | Split-Phase |
| Thrust Rating | 300 lb |
| Standards | ANSI/NSF 61 |
| Motor Thermal Protection | Built-In Lightning Arrestor |
| Height | 10-1/4 in |
| Full Load Amps | 8 A |
| Diaphragm Type | Pressure Equalizing |
| Motor Application | Pumps |
| Stator Type | Hermetically Sealed |
| Hz | 60 Hz |
| Overload Relay Amp Setting | 10.0 A |
| Starter Required | No |
| Motor Mounting Position | Vertical Shaft Up |
| Motor Frame Material | Stainless Steel |
| CC Number | Not Applicable |
| Finish | Not Applicable |
| Includes | Not Applicable |
| Regreasable Bearings | Not Applicable |
| Motor Shaft Design | Splined |
| No. of Speeds | Not Applicable |
| Length Less Shaft | 8-3/4 in |
| Inverter Rated | Not Inverter Rated |
| Nominal Efficiency | 51% |
| Bearing Protection | Not Applicable |
| Frame | Not Applicable |
| Duty Cycle | Continuous |
| Conduit Box Location | Not Applicable |
| Shaft Dia. | 5/8 in |
| NEMA Design | Not Applicable |
| Conduit Box Position | Not Applicable |
| Weight | 17 lb |
| Overall Length | 8-3/4 in |
| Resilient Ring Dia. | Not Applicable |
| Body Dia. | 3.8 in |
| Motor Mounting Type | NEMA Pump Mounting |
| Inverter Rating | Not Applicable |
| Shaft Length | 9-1/2 in |
| Manufacturers Warranty Length | 1 yr |
| Ins. Class | B |
| Ring to Ring Center | Not Applicable |
| Part Winding Start Capable | No |
| Bolt Circle Dia. | 2-7/8 in |
| Number of Speeds | Not Applicable |
| Overload Relay Current | 10 A |
| Shaft Diameter | 5/8 in |
| Bolt Circle Diameter | 2-7/8 in |
| Shaft Design | Splined |
| Efficiency Rating | Not Applicable |
| Frame Size | Not Applicable |
| Includes Low Temperature Monitor | Low Temperature Monitor Not Included |
| Full Load Current @ 60 Hz | 8 A |
| Product Type | Pump Motor |
| Bearing Protection Type | Not Applicable |
| Bearing Lubrication Type | Not Applicable |
| Frequency | 60 Hz |
| Nameplate Service Factor @ 60 Hz | 1.15 |
| NEMA Design Class | Not Applicable |
| Frame Finish | Not Applicable |
| Series | 4" SUPER STAINLESS SUBMERSIBLE MOTORS |
| Manufacturers Warranty | 1 yr |
| Overload Relay Maximum Amp Setting | 12 A |
| Motor Enclosure Type | Totally Enclosed Non-Ventilated |
| Ring-to-Ring Center | Not Applicable |
| Sub Application | Deep Well Submersible Pump |
| Application | Pump |
| Requires Overload Relay | No |
| Insulation Class | B |
| Service Factor Current | 9.2 A |
| Bearing Type | Kingsbury |
| Resilient Ring Diameter | Not Applicable |
| Includes Diaphragm | Diaphragm Included |
| Frame Material | Stainless Steel |
| Mounting Position | Vertical Shaft Up |
| Body Diameter | 3.8 in |
| Wire Rope Length | 8-3/4 in |
| Length | 8-3/4 in |
| Country of Origin (subject to change) | Mexico |
| Package Quantity | 1 |