The ZORO SELECT - 1ZAJ2 is a Sheet Stock plastic sheet, intended for use in a variety of industrial applications. This off-white HDPE (High-Density Polyethylene) material can be cut, shaped, or molded into different forms depending on the specific requirements of the project. It has been tested for resistance against certain corrosive substances and chemicals. It's recommended usage is in environments where these substances are present.
- Corrosion and Chemical Resistance: The sheet has demonstrated some level of resistance to certain corrosive substances and chemicals during testing.
- Friction Coefficient & Rating: With a measured friction coefficient of 0.2, the product may exhibit lower levels of friction when interacting with other surfaces.
- Impact Strength & Rating: The product's impact strength measurement is 1.30 ft-lb/in; however, actual performance may vary based on conditions.
- Machinability: The product has received an average machinability rating based on standard tests; actual results may depend on specific tooling conditions.
- Temperature Range: This plastic sheet has been tested under temperatures ranging from -58 Degrees F to 176 Degrees F; performance outside these ranges hasn't been evaluated.
- Tensile Strength & Rating: The measured tensile strength of this product is 4,600 psi; actual performance may vary based on usage conditions.
| Item | Sheet Stock |
|---|---|
| Plastic Material | HDPE |
| Plastic Thickness | 1/4 in |
| Plastic Width | 12 in |
| Plastic Length | 24 in |
| Plastic Color | Off-White |
| Max. Temp. (F) | 176 |
| Min. Temp. (F) | -58 Degrees F |
| Color | Off-White |
| Operating Temp. Range | -58 to 176 deg F |
| Plastic Properties | Chemical/Corrosion Resistant, Non-Friction Surface, Moisture Resistant, Wear Material |
| Plastic Grouping | Sheet Stock |
| Thickness Tolerance | +/-10% |
| Tensile Strength | 4,600 psi |
| Impact Strength | 1.94 ft-lb/in |
| Width Tolerance | +/-0.25 in |
| Length Tolerance | +/-0.250 in |
| Standards | ASTM D2239, Dept of Canadian Agriculture, FDA, USDA |
| Material Color Family | Off-White |
| Material Type | Corrosion Resistant |
| Length | 24" |
| Width | 12" |
| Thickness | 1/4 in |
| Material | HDPE |
| Corrosion and Chemical Resistance | Good |
| UV Resistant | No |
| Machinability | 80 % |
| Wear Factor | Good |
| Maximum Temperature | 180 deg F |
| Water Absorption | 0.01% |
| Minimum Temperature | -40 deg F |
| Plastic Hardness Rating | Medium |
| Impact Strength Rating | Poor |
| Plastic Clarity | Opaque |
| Plastic Thickness Tolerance | +/-10% |
| Grade | Standard |
| Friction Coefficient | 0.2 |
| Friction Rating | Very Slippery |
| Plastic Hardness | 70D |
| Tensile Strength Rating | Poor |
| Plastic Length Tolerance | +/-1/4 in |
| Temperature Range | -58 to 176 deg F |
| Plastic Width Tolerance | +/-1/4 in |
| Shape | Rectangle |
| Water Absorption Rating | Excellent |
| Nominal Size | 12 in W x 24 in L |
| Plastic Density | 0.93 g/cc |
| Backing Type | Not Applicable |
| Maximum Adhesive Temperature | 203 deg F |
| Minimum Adhesive Temperature | 70 deg F |
| UL 752 Ballistic Rating | Not Applicable |
| Product Type | Plastic Sheet |
| Filler Material | Not Applicable |
| Elongation | 300 % |
| Number of Walls | Not Applicable |
| Metal Detectable | No |
| Shore Hardness | 70 Shore D |
| Dielectric Strength | 50 kV/mm |
| Coefficient of Thermal Expansion | 0.55 x 10^-5 in/in/ Degrees F |
| Product Form | Sheet |
| Light Transmission | 90 % |
| Flexural Modulus | 174 ksi |
| Rockwell Hardness | 64 HRM |
| Wear Rate | 6.53 x 10^-6 cu mm/N-m |
| UV-Resistant | UV-Resistant |
| Scratch-Resistant | Scratch-Resistant |
| FDA Compliance | 21 CFR 177.1520 |
| Static-Resistant | Not Static-Resistant |
| Fabrication | Extruded |
| Country of Origin (subject to change) | Multiple |
| Package Quantity | 1 |